• UNIQUE SHAPE OF TANK OFFERING GREATER RESISTANCE TO STRESS RELATED FACTORS.
• LOW PROFILE TANK FOR MAXIMUM VISIBILTY AND STABILITY.
• "V" SHAPE BOTTOM FOR MORE COMPLETE CLEAN OUT.
• STANDARD EXTERIOR FINISH: EPOXY PRIMER AND URETHANE PAINT.
• AVAILABLE WITH "STEEL PLUS" OPTION INCLUDING A 10 YEAR WARRANTY AGAINST RUST OUT.
• SIZE OF TANK FROM 2350 TO 9500 US GALLONS
• WE ALSO MANUFACTURE CUSTOM BUILT TRUCK MOUNT TANKERS

• New design of baffles allowing for easier access and better visual inspection inside the spreader.
• Independent front and back fill indicators with float built form P.V.C. pipe filled with rigid urethane foam mounted on nylon and stainless steel pivot.
• Adjustable front slope to bring more solid material towards the pump.
• Pump intake lowered 5" to empty the spreader thoroughly. (N. A. on model EL-66)
• Std impeller: 22 - 1/2 Ø X 540 R.P.M.
• Bearing assembly of impeller built with tapered roller bearings in oil bath sealed with 3 greasable seals.
• Standard P.T.O.: series 35 with single universal joint to spread manure in straight line without turning.
  
  
  
  back to top

• 6" Ø drain with quick opening at spreader rear end.
• 4" Ø drain with quick clamp to empty impeller housing.
• 6" Ø drain discharge pipe with flexible hose connection
• 3-1/2 Ø standard spreading nozzle.

• Constant velocity P.T.O. to spread manure while gradually turning with the spreader.
• P.T.O. 1000 R.P. M. available with 4 sizes of impellers according to P.T.O. R.P.M., tractor HP, manure consistency and desired spreading speed.
• 4" and 5" Ø spreading nozzle for faster unloading.

• Three 6" Ø clean-out openings on top of spreader to easily clean the inside with a pressure washer.
• Directional valve and inside agitation kit to maintain solid material in suspension inside spreader while traveling.
• Low level spreading nozzle at 36" from ground for precise and narrower spreading pattern in windy conditions.
  
  back to top

• Unique shape of under carriage cross member allowing a lower profile spreader.
• "Closed" tandem design for a better torsion resistance than a conventional tandem.
• Greasable walking tandem spindle pivoting on brass bushings.
• Pivot-point of walking tandem if off centered to allow for a smoother ride over rough ground and reduce weight on front wheels for easier turning.
• Under carriage tank supports located very close to the wheels to avoid flexing and torsion.
• Bolted axles for easy servicing.
• Adjustable under carriage to increase or decrease the weight on the tractor draw bar.
• Heavy-duty tow bar bolted to full length tank skids to pull the under carriage without transmitting any stress to the tank.

The power - steering system fed by the tractor steers the directional wheels of the spreader to follow the tractor turning angle allowing easy sharp turns without destroying the vegetation.

The power - steering valve control mechanism has a hinge to easily connect the spreader to the tractor draw bar and is designed to transmit the tractor turning angle to the power - steering valve without being affected by any play between the spreader hitch and the tractor draw bar.

One push - pull cable with one end attached to the steering arm of there directional wheels and the other end attached to the valve of the power - steering constantly indicates the steering angle of the directional wheels to maintain them at the same turning angle as the tractor.

Pre - loaded springs on the power - steering cylinders bring automatically the directional wheels back in straight line position as soon as the power - steering cylinders are no longer fed.

A spring loaded mechanism protects the power - steering control if tractor is turning without supplying hydraulic oil pressure to the directional valve.

Lagoon pumps

• Faster agitation than with any existing pump or agitator.
• Agitation without odors or splashing around the manure reservoir.
• Heavy duty 3" dia. propeller shaft mounted in oil bath protected by a greasable 3 seals mechanism.
• 3 propellers available for 540 RPM P.T.O.
  75 HP = 23,000 US GPM of agitation
  100 HP = 33,500 US GPM of agitation
  140 HP = 45,500 US GPM of agitation
  

Manure Pumps

Super pump standard with a single high capacity nozzle for manure with limited amount of chopped bedding.
Available with the option twin nozzles to agitate both bottom sediments and surface of pit at the same time.

Super pump standard with a single nozzle

• Horizonal operating radius of 220 degrees and 60 degree vertical with 3" and 3.5" dia. nozzle end.
• 20" dia. impeller for 540 or 1000 RPM P.T.O.
• 28" dia. impeller optional for 540 RPM P.T. O.
• Heavy duty gear box available with different ratios for different sizes of tractors.

Super pump with twin 3" dia. nozzles option

• Upper nozzle with horizontal operating radius of 200 degrees and 60 degrees vertical.
• Bottom nozzle with horizontal operating radius of 200 degrees.
• Provides full time bottom agitation

More features:

• Bottom bearing assembly in oil bath protected by a greasable 3 seals mechanism.
• Rotative directional valve designed to be operated while P.T.O. is at low RPM
• 25' loading pipe with tripod.
• Oil cooler on non-immersed gear boxes (optional on Agi-pome and Super pump.)
• Knife kit on propeller to cut bedding (Optional on Agi-Pompe)
• Nozzle articulation with stainless steel ball in a socket (standard on Agi-pompe and Super pump)
• Hydraulic rotative direectional valve (standard on Agi-pompe and Super pump)